Search found 232 matches

youre right-ive just checked my table and ive given the crank pin diameter not the big end...will edit the post

you should also be able to fit a complete crank-rod-piston assembly from a later model motor

bio-gas processer...nice blue-flamer

he is just a patsy being used to make you feel good about losing even more freedoms

best to stay away from synthetics...can clean and reuse the sump filter if its not ripped...the side filter will need replacing

A....22mm piston wrist pin
B....34mm big end
C..136mm con rod centre to centre
D..?

A..?

all the best of the season, weve had xmas dinner, opened the pressies, put the kids to bed, and are now getting wasted - its pissin down, the snows melting away...tomorrows supposed to lightly snow-me ...

- youre on the right track bennecc-i had a slight block that ive edited but the basics are correct

- the pictures show bullet type connectors not spade type

- the loop is completed by the eart ...

- actually, to instal a kill switch, you dont want to branch out into 2 wires as then the kill switch is effectively bypassed...cut the live wire feeding the TCI, fit a single female to the live end a ...

[img]http://www.xs650.biz/images/10/783.jpg[/img][img]http://www.xs650.biz/images/10/780.jpg[/img]
insulation - round double female or round single female
[img]http://www.xs650.biz/images/10/782.jpg ...

- roy - i know where there is a new unused set of stock exhausts, but for 1300 euro im not interested at the moment...i can get more than a good bike for that...i also know where there is a 78 std sti ...

- i have 5 here...in europe...was talking to a yammie dealer at our stammtisch last friday night about SR400's from japan, as the 500 has such a cult following here i was asking why they dont import t ...

- i got roughly 4.0mm thick, 13.0mm long and 6.0mm high...xs key

- yea we got that on german tv last night too...i must say ive seen better breasts tho...id rather remember invercargill as being the home of bert, great oysters and yes even the proverbial horses mou ...

580mm from centre of tank bolt to centre of frame tube in my '82

...your engine nr will tell you what year it is - if it is different from your frame nr then its been swapped...knowing what year the engine and frames are doesnt mean that those are the original carb ...

- are you sure you need it...youre estart is either disconnected, removed or not functioning so there is no heavy current passing through the system and the motor is solid mounted, ie self-earthing
...

...as its a great source of nutrient, a discerning shitter will do so where its likely to be most productive

...bar end weights
...fill bars with lead
...rephase
...try johns low comp mod
...had a mate lose a hand once-replaced with a hook, he still rides and doesnt at all suffer from this
...could try ...

... Mark Whitebook from Probe Engineering in California (949-489-9561) makes these electronic igns for the 650, 650/277 and the 650/270.

... Newtronics http://www.newtronic.co.uk/ make a unit for ...

...we had 3 frosts late oct then nothing-havent had to scrape the car windows since...snowing again this morning though - in about 30 mins, after my coffee, im off for a ride...time to terrorise those ...

- the 7 wire may be 3 field , 2 pos and 2 neg...the 6 wire may have a voltage sensor wire for the estart, 1 pos and 1 neg...

- wont know without knowing the cable colours...have a pic?

- as far as im aware they were all like that...early GS1000 swing arm bolts fit once the head is shaped

- nice score....your guard will be the longer standard

- just actually had a look at what youve got - i like these motors the best ... ok the frame is rather flexy, it has the 34mm forks, the old ...

What Happened to 650rider.com?

Yamaha xs650